The basic NPAC model is made to counteract the one-way flow-through forces caused by negative building pressure or by wind effects.
Features
Single Nozzle and Intake
Proprietary Nozzle Design
Greatly Diminishes One-Way Air Flow Caused By Building Air Imbalances
Horizontal, Curvilinear, Recirculatory Air Flow
Powder Coated Steel
Metal Clad Insulation When Required
Supply where indicated on plans HCR Model NPAC Air Door for doorways with low temperature differentials and or for temperatures above freezing.
Air Door to be powder coated cold-rolled steel. Powder coating meets 500 hour salt spray test.
NEMA 1 Power/control panel complete. Model NPAC equipment cabinet houses the centrifugal fan, fan motor, fan drive components, and prewired electrical components. Service door(s) are provide, if required, to allow access to all internal components. Motor is controlled by VFD (Variable Frequency Drive). Single point electrical connection.
Air Door to have two side plenums: one with discharge nozzle, the other with an intake.
Discharge nozzle is easily adjustable to maximize air block. Air volume adjustment mechanisms are easily accessible without removing any covers or secondary openings.
Unit can be mounted on either side of wall. Depending on temperature differential insulation cladding may be required.
Air Door assembly is structurally self supporting. All hardware has protective coating against corrosion.
Air Door power to be 208, 240, or 480 volt AC, 60 Hertz, 3 phase. Visible signal light to show when motor is not running. Complete door assembly to be ready for connection to power. (Architect to designate responsibility for field wiring.) The Model CAC Air Curtain is for applications where temperatures and humidity exceed the limits of our Model AC. A heater unit is added to condition the air as it mixes inside the vestibule.
The Model CAC automatically adjusts as conditions change to optimize performance and reduce energy consumption.
With the use of HCR sensors and software, Model CAC can be integrated into a facility's refrigeration control and monitoring system. This allows not only remote monitoring but remote adjusting of the HCR equipment.
Features
Single Nozzle And Intake
Proprietary Nozzle Design
Greatly Diminishes Air and Moisture Infiltration
Horizontal, Curvilinear,Recirculatory Air Flow
Powder Coated Steel
Metal Clad Insulation When Required
Cooler or Ambient Door Specifications
Supply where indicated on plans HCR Model AC Air Door for doorways with low temperature differential and or for temperatures above freezing.
Air Door to be powder coated cold-rolled steel. Powder coating meets 500 hour salt spray test.
NEMA 1 Power/control panel complete. Model AC equipment cabinet houses the centrifugal fan and prewired electrical components. Service door(s) are provided, if required, to allow access to all internal components. Motor is controlled by VFD (Variable Frequency Drive). Single point electrical connection.
Air Door to have two side plenums: one with discharge nozzle, the other with an intake.
Discharge nozzle is easily adjustable to maximize air block. Air volume adjustment mechanisms are easily accessible without removing any covers or secondary openings.
Unit can be mounted on either side of wall. Depending on temperature differential, insulation cladding may be required.
Air Door assembly is structurally self-supporting. All hardware has protective coating against corrosion.
Air Door power to be 208, 240, or 480 volt AC, 60 Hertz, 3 phase. Visible signal light to show when motor is not running. Complete door assembly to be ready for connection to power. (Architect to designate responsibility for field wiring.)
Freezer Door Specifications:
Freezer Air Door specifications to be same as cooler or ambient Air Door except for these substitutions and additions: Supply where indicated on plans HCR Model CAC for freezers doorways with temperature differentials below 30 degrees Fahrenheit. Provide insulation cladding as required for application.
Cabinet can be mounted either warm side or cold side of wall.
Electric resistive heat or waste heat reclaim as required. Model AC is HCR's basic unit -- Horizontal, Curvilinear, and Recirculatory. Its air stream produces counter-flow forces equal and opposite to the two-way flow-through forces caused by air temperature differences.
Features
Wide open environment while maintaining temperature
Significantly reduces two-way air exchange
Greatly diminishes air infiltration
Mixes air at the interface between room air and
the air curtain's air stream
For open doorways between cooler-to-cooler,
cooler-to-ambient, and freezer-to-freezer
Available in stainless and powder-coat finishes
Can be used between two freezers without requiring any heat
Model AC is HCR's basic unit -- Horizontal, Curvilinear, and Recirculatory. Its air stream produces counter-flow forces equal and opposite to the two-way flow-through forces caused by air temperature differences. Recommended up to 14 ft. high
The CHA meets all conditions of the International Energy Conservation Code (IECC) approving the use of an air curtain as an exception to building a vestibule.
Standard grille color: White (other colors and materials available)
Hinged bottom panel for easy access
Folded metal border ensures straight lines against a flat ceiling
¾ hp motor(s)
High-efficiency discharge plenum
Fully assembled and factory tested
ETL listed
Made in the USA Recommended for windows up to 42 in. high
The PTW is specifically designed to stop outside air and vehicle fumes from infiltrating a drive-thru window.
304 stainless steel
107 watt motor
Unit mounted variable speed dial
120V power cord
Swivel mounting brackets
Fully assembled and factory tested
ETL listed
Unit with electric heat available
Made in the USA Recommended up to 10 ft. high
The BCT is a versatile and durable air curtain that is designed to stop flying insects, dust, and other small contaminants from infiltrating an opening.
304 stainless steel case
¾ hp single speed motor(s)
High-efficiency discharge plenum
Fully assembled and factory tested
ETL listed for indoor/outdoor use
USDA compliant
FDA compliant
Made in the USA Recommended up to 12 ft. high
Maintaining interior temperature, especially near doorways, is a challenge shared by building designers as well as building owners. The Climate Control Series is the most effective solution to this problem. Durable stainless steel construction, noise reducing plenum discharge, and a wide variety of heating options make this series the optimal choice for commercial and light industrial doors.
304 stainless steel case
High-efficiency discharge plenum
Fully assembled and factory tested
Made in the USA Recommended up to 14 ft. high
The ETA meets all conditions of the International Energy Conservation Code (IECC) approving the use of an air curtain as an exception to building a vestibule.
304 stainless steel case
¾ hp motor(s)
High-efficiency discharge plenum
Fully assembled and factory tested
ETL listed
Made in the USA Recommended up to 11 ft. high
The CED is the benchmark for entry door air curtains. It’s long been Powered Aire’s best-selling commercial model due to its minimum objectionable airflow, ultra-quiet plenum design, and durable stainless steel case.
304 stainless steel case
½ hp dual speed motor(s)
High-efficiency discharge plenum
Fully assembled and factory tested
ETL listed
Made in the USAModel CAC Negative Pressure Air Curtain - ADS-403
The Model CAC Air Curtain - ADS-400
Model AC Air Curtain - ADS-400
Chameleon Vestibule Exception (CHA)
Pass Thru Window (PTW)
Insect Control 10ft High (BCT)
Climate Control (ETD/THS/TIG/TDG)
Exposed Vestibule Exception (ETA)
Customer Entry Door (CED/CHS)
AIR CURTAINS
LETTERS FROM OUR CUSTOMERS
Joe,
Just a quick note to say how pleased I am with my 3 new garage doors and the fellows who installed them. Both your workers did a very professional job for me. The doors roll freely, the capping edges are sharp and precise and the caulking neatly edged. They worked hard and you should be very proud of the way they represented your company. Please pass my thoughts along to both of them. Thanks for a job well done. I will most certainly recommend Apex to anyone who is in need of garage doors in the future.
Regards,
Bob M.
Dear Apex:
Thank you so much our 2 new doors look great!!
Dorothy Z.
Dear Apex:
Thank you for a wonderful job on this installation. It was a pleasure to work with you and your staff and it will be my pleasure to recommend you to others.
Andrew L. M, E.