Commercial Door Operators

LJ8950W Light-Duty Commercial Door Operator for Rolling Doors

• Wallmount with smaller, lighter rolling doors and grilles
• Rated duty cycle: Maximum 10 cycles per hour; Fewer than 25 cycles per day
• Easily connect the operator to the facility's network with built-in Wi-Fi®

LJ8900W Light-Duty Commercial Door Operator for Sectional Doors

LiftMaster's KPR2000 is a feature-rich keypad and proximity card reader access controller that is simple to install and looks great, making it an excellent choice for both Residential and Commercial applications.

• Supports a maximum of 2,000 users in multiple access configurations
• Supports HID 26-bit and 30-bit Wiegand proximity card formats
• Designed for outdoor environments with a sealed, weather proof design allowing you to easily mount anywhere
• Provides stand alone or pass-thru operation Latch Mode allows you to hold open a door or gate for an extended period of time
• Includes Rapid Programming and Block Enrollment capability, "Add" and "Delete" program cards
• Programmable Output Relay with adjustable contact time appropriate for Gate Operator, Commercial Door Operator, Door Strike or Solenoid Lock
• Capable of networking two KPR2000s, PPWR to the KPR2000 or to most Access Control Systems

MH Medium-Duty Hoist Operator

• For use on smaller, lighter commercial doors with mid-range duty cycle requirements
• Rated duty cycle: Maximum 12 cycles per hour; Less than 50 cycles per day
• Wall mount for high or vertical lift sectional doors or small rolling doors and grilles
• Chain hoist with electric interlock for manual operation in an emergency

MT Medium-Duty Trolley Operator

Sections

• 2" thick sections are foamed in place with polyurethane for superior R-value
• Thermally-broken to eliminate thermal convection
• Gasket seal between sections provide for an extremely tight weatherseal
• Concealed steel back-up plates run from top to bottom of each section for secure hardware attachment
• Bottom "U" type astragal is a standard feature
• Available in white

Tracks

• Available in bracket mount, angle mount, clip angle mount, 12" radius, 15" radius, high lift, vertical lift, roof pitch, or dual track low headroom

Hardware

• Package includes 14 gauge or 11 gauge hinges, as specified
• 2" or 3" short-stem or long-stem ball bearing rollers
• Heavy-duty adjustable top roller brackets springs
• Torsion springs are helically wound with stress relieved, oil-tempered wire
• Springs are individually calibrated for each door
• Counter-balance torsion shafts are galvanized for rust resistance
• High cycle spring options may be specified

MGJ Medium-Duty Gear-Reduced Jackshaft Operator

• For use on mid-range duty-cycle applications when specifications require a gearhead reducer
• Rated duty cycle: Maximum 12 cycles per hour; Less than 50 cycles per day
• Wall mount for high or vertical lift sectional doors or small rolling doors and grilles
• Floor level disconnect disengages operator for manual lifting in an emergency

MHS Medium-Duty Slow-Speed Hoist Operator

• For use on rolling sheet doors which require slower speeds
• Rated duty cycle: Maximum 12 cycles per hour; less than 50 cycles per day
• Slow speed operation with electric interlock and chain hoist for manual operation in an emergency
• Wall mount for small rolling sheet doors

MJMedium-Duty Jackshaft Operator

• For use on smaller, lighter commercial doors with mid-range duty-cycle requirements
• Rated duty cycle: Maximum 12 cycles per hour; Less than 50 cycles per day
• Floor level disconnect disengages operator manual lifting in an emergency
• Wall mount for high or vertical lift sectional doors or small rolling doors and grilles

DJ Door Lock Jackshaft Operator - Logic 5.0

• For shopping malls and cafeterias. Includes floor-level chain hoist for manual lifting of smaller/lighter doors/grilles
• Rated duty cycle: 25 per hour; Up to 90 cycles per day
• Internal doorlock sensor prevents damage by restricting door activation while door is locked
• Wall or hood mounts for rolling doors/grilles and sectional overhead doors with vertical high lift

J Jackshaft Operator - Logic 5.0

• For use on industrial applications with smaller sectional doors
• Rated duty cycle: 25 per hour; Up to 90 cycles per day
• Side mounts to the wall for vertical or high-lift doors
• Smaller rolling doors and grilles. Wall or hood mounts

DHJ Door Lock Hoist/Jackshaft Operator - Logic 5.0

• For shopping malls and cafeterias. Includes floor-level chain hoist for larger, heavier doors/grilles
• Rated duty cycle: 25 per hour; Up to 90 cycles per day
• Internal door lock sensor prevents damage by restricting door activation while door is locked
• Wall or hood mounts for rolling doors/grilles and sectional overhead doors with vertical high lift

H Hoist Operator

• Optimal for industrial applications with larger sectional overhead doors
• Rated duty cycle: 25 per hour; Up to 90 cycles per day
• Side mounts to the wall for vertical or high-lift doors
• Rolling doors and grilles. Wall or hood mounts

GSD Gearhead Slide Door Operator - Logic 5.0

• For use on smaller, lighter commercial doors with mid-range duty-cycle requirements
• Rated duty cycle: Maximum 12 cycles per hour; Less than 50 cycles per day
• Floor level disconnect disengages operator manual lifting in an emergency
• Wall mount for high or vertical lift sectional doors or small rolling doors and grilles

GT Gearhead Trolley Operator - Logic 5.0

• For use on heavy industrial, high cycle applications. Lubricated gear system and numerous custom modifications
• Rated duty cycle: 25 per hour; Greater than 90 cycles per day
• Suspends from the ceiling. Directly attaches to drive and controls the door
• Sectional overhead doors

SD Slide Door Operator - Logic 5.0

• For use on industrial slide doors
• Rated duty cycle: 25 per hour; Up to 90 cycles per day
• Ideal for farm and agriculture buildings, storages sheds and hangars

GH Gearhead Hoist Operator - Logic 5.0

• For use on heavy industrial, high-cycle doors. Lubricated gear system and numerous custom modifications
• Rated duty cycle: 25 per hour; Greater than 90 cycles per day
• Larger/heavier sectional overhead doors. Side mounts to the wall for vertical or high-lift doors
• Larger/heavier rolling door and grilles

T Trolley Operator - Logic 5.0

• For use on standard-lift sectional overhead doors
• Rated duty cycle: 25 per hour; Up to 90 cycles per day
• Suspends from the ceiling. Directly attaches to drive and controls the door

FDC Retro Operator

The Automated Fire Door Controller provides a motorized fire-door solution, without the loss of spring tension, for added safety when dealing with high pedestrian traffic.

• Time-delayed automatic closing
• Monitored 72-hour battery backup
• Low-battery warning
• Programmable closing-function selection
• Keyed test station
• Electronic thermal sensors (field installed)
• Detector/alarm input
• Adjustable linear-driven limit switches
• 3-button open/close/stop control station
• NEMA 1 enclosure
• UL® Listed (UL325) regulatory label support/tracking

FDHS16LIFTRETRO Manual Fire Door Operator

Manual fire door operator The LiftMaster Retrofit Manual Fire Door Hoist Operator provides manual door operation using a floor level hand chain allowing a user to open and close their fire door with ease.

• Spring loaded release arm
• Adjustable governor
• Automatic closing without loss of spring tension
• Left or right side door mounting
• Holding brake

LM21AFCB
Advanced fire control release device

Advanced fire control release device The AFCB release device is designed to be used in conjunction with a standard commercial door operator to provide a fully automated door closing system. For use with motorized doors incorporating a reversing electric safety edge, this 120VAC device can power up to 4 smoke detectors and 2 horn/strobes. This system combines state-of-the-art functionality and advanced features typically found on special-order fire door operators.

LM21XPBB
Extended performance release device

The AFCB release device is designed to be used in conjunction with a standard commercial door operator to provide a fully automated door closing system. For use with motorized doors incorporating a reversing electric safety edge, this 120VAC device can power up to 4 smoke detectors and 2 horn/strobes. This system combines state-of-the-art functionality and advanced features typically found on special-order fire door operators.

HCTDCUL
Specialty Overhead Operator

The Automated Fire Door Controller provides a motorized fire-door solution, without the loss of spring tension, for added safety when dealing with high pedestrian traffic.

• Engineered to increase uptime and provide powerful, reliable performance
• Noise-isolating design provides for exceptionally smooth and quiet operation
• Selectable speed control opens up to 11″ inches per second to keep traffic flowing
• Integrates easily with LiftMaster Access Control Technology

DDO8900W Light-Duty Commercial Dock Door Operator

Manual fire door operator The LiftMaster Retrofit Manual Fire Door Hoist Operator provides manual door operation using a floor level hand chain allowing a user to open and close their fire door with ease.

• For full vertical or high-lift sectional commercial and dock doors
• LMi5 Interface Device monitors up to 5 external sensors around the dock door with myQ® Facility
• Opens 50% faster in the up direction
• Easily connect the operator to the facility's network with built-in Wi-Fi®
• Annual subscription to myQ Facility, first six months included

VFOH - Variable Speed Front of Hood Operator

• Front of Hood Mount for Rolling Steel Doors and Grilles
• Variable speed up to 12"/sec with smooth start/stop feature
• Floor level controls with intuitive menu driven interface